short description

Product description

Version

• With cross-counterflow heat exchanger and preheating register, outside and outgoing air connections to the left, outlet at the top.

Features

• Decentralised RLT air handling unit with very high heat recovery for use in classrooms, nurseries, offices, doctors' surgeries, shops, meeting rooms and similar.
• The unit is ceiling-mounted and can also be partially integrated into suspended ceilings.
• On the room air side, the unit can be fitted with free air discharge and intake as well as with supply and exhaust air connections.
• Supply air grilles with adjustable air guide slats are already integrated in the unit.
• The exhaust air opening is located on the left-hand side of the unit.
• The unit can optionally be fitted with a duct system for the supply and/or exhaust air.
• The integrated automatically closing shutters for outside and outgoing air close in the event of a power failure or when the unit is switched off.
• The generously dimensioned heat exchangers with their efficiency of up to approx. 95 % and the very low internal pressure loss ensure low primary energy consumption and high energy gains.
• All units are fitted with a condensate lift pump.

Housing

• Design based on VDI 6022 / VDI 3803.
• High-quality, double-walled housing made of galvanised sheet steel.
• The insulation is 20-60 mm and consists of a combination of special foams of thermal conductivity group 040.
• The acoustic insulation material of the interior insulation is made of normally flammable special foam of building material class B2 (DIN 4102-1).
• The visible areas of the unit’s cladding consist of design panels in the colour pure white, similar to RAL 9010, smooth matt.
• With the special sliding suspension ('slotted hole'), the units can be mounted directly under the ceiling.

Standard heat exchanger

• Highly efficient cross-counterflow plate heat exchanger made of plastic (PS) with a maximum degree of heat provision of approx. 95 %

Fans

• Single inlet, highly energy-efficient fans with backward curved 3D impeller made of fibre-reinforced plastic.
• Electronically commutated (EC) external rotor motor with integrated electronics and mains adapter.

Control

• CO2 sensor integrated in the exhaust air (as standard) enables smart demand-driven ventilation operation.
• The air volume is continuously adjusted to the actual air requirement – this enables maximum efficient ventilation unit operation.
• Optional external sensors or higher-level building control system possible.
• Frost protection function depending on the outgoing air temperature via preheater (for units with "E" enthalpy heat exchanger, the preheating register is an optional accessory).
• All geniovent.x devices can be controlled via application using the integrated LAN interface.
• The units can therefore be operated on the move or from home, e.g. smartphone.
• Live reports, user administration, control and adjustment via tablet, laptop and PC.
• USB connection as a standard feature for commissioning, control system update and service.
• All units have several operating modes:
• 2 automatic operating modes (Auto Sensor / Auto Time)
• 4 manual operating modes (ECO exhaust air / ECO supply air / MANUAL / OFF)
• Using the time programmes (standard and holiday time programme), not only ventilation levels can be selected but also functions set (e.g. night cooling, flush mode, motion detector mode) or times for demand-driven operation (e.g. sensor mode) chosen.
• All geniovent.x units are characterised by an energy-optimised frost protection strategy that is adapted to actual requirements.
• In addition, all units have a multifunction contact for controlling, e.g., an unregulated pump or operating, fault and filter change indicator or preheating register or supplementary heat register or external shutters or cooling.
• Two input contacts (12 V and 230 V) are available for, e.g., safety shutdown.
• Various inputs/outputs enable a control connection to other technical devices or switching points (e.g. unit release or fume cupboard operation)

Control system

• Continuously variable demand-driven adaptation of air volumes.
• 4 temperature sensors in the outside air, outgoing air, supply air and exhaust air.
• 1 CO2 sensor in the exhaust air connection.
• Up to 3 external sensors of different types (CO2, VOC, humidity) or push-button and switching contacts (motion detector, external start/stop, fume cupboard operation and night cooling and flush mode) can be connected.
• Inputs for safety shutdown via 12V contact or 230V contact (e.g. smoke detector, fire alarm, differential pressureless fireplace).
• Various inputs and outputs allow the a control connection of the ventilation unit to other technical building devices.

RLS 1 WR control unit

• Supplied as a simple control panel.
• Switching the ventilation levels, maintenance display, fault messages.

RLS T1 SYS touchscreen control panel, optional

• Touchscreen control panel for geniovent.x units with control.
• Graphic, high-resolution colour TFT display with easy-to-use, intuitive menu navigation.
• For operation and configuration of various time programmes, operating modes, ventilation levels, automatic night cooling, flush mode, etc. as well as to display status information and alarm messages.
• Integrated room temperature sensor.
• Multi-unit capability: up to 10 different geniovent.x units can be controlled with the control unit.
• Updateable.

Modbus

• Integrated MODBUS interface (TCP/IP and RTU) enables an integration in the building control system.

BACnet

• Integrated BACnet interface (TCP/IP) enables an integration in the building control system.

EnOcean

• Optional EnOcean plug-in module E-SM for integrating the ventilation unit into the "EnOcean world" "www.enocean-alliance.org" Not possible in conjunction with the RLS T1 SYS touchscreen control panel!

KNX

• Optional KNX plug-in module K-SM allows for connection to building control system, “www.knx.org”.

Additional circuit board ZP 1

• Optional additional circuit board ZP 1 for controlling e.g. a second heater in the geniovent.x ventilation unit, 3-way shutter or regulated pump or air shutter of a zone control.